Wood Drying Process

Wood Drying is the process of reducing the moisture of the wood before its use. Wood needs to be dried in order to use it for commercial purposes; be it in construction or even using it as fire wood, moisture content makes usage of wood difficult.

There are a number of reasons why wood has to go through the process of drying

  • Dried timer is lighter and therefore transportation is easy.
  • Dry wood has good machining, gluing and good working properties rather that wet wood.
  • The electrical and thermal insulation properties of wood are improved by drying.
  • Wood drying is important to avoid decay of wood or any fungus growth, which might spoil the wood and making it difficult to use.
  • Drying process also increases the strength of the wood.

 

COMMON DRYING METHODS

Commonly used drying methods

The economically feasible, industry-adoptedsystems especially differ in the degree of environmental control they provide.

Air drying: Wood is kept in a shed or covered by a roof and left for natural air drying. They are only protected from rainfall.

Forced Drying: Forced drying is a process of drying wood with the help of fans in addition to natural air circulation. Wood is again protected from rainfall by keeping it in a shed. This process is time consuming.

LOW TEMPRETURE DRYING:
In this method, wood is dried under controlled temperature conditions. Wood is kept in a building where the temperature is set as high as 130oF or usually between 80oF to 110o and control humidity through help of vents. Circulation of wind is achieved through fans. There are 3 types of low temperature drying

  • Solar heater or solar dryer: Less expensive method but weather dependant
  • Dehumidifier dryer : very expensive yet very good control system
  • Steam heated dryer: Not very expensive but the control system is not good.



Kiln drying

Kiln drying is a process where heat is introduced and heating conditions are controlled in Kiln order to dry the wood. Such a process of drying wood is faster and advantageous where weather conditions do not help in achieving the best drying results. The main elements in Kiln drying are:

  • Kiln: The kiln chamber is built of bricks or hollow cement concrete slabs. A few modern kilns are made up of sheet metal or aluminium where the construction walls are sandwiched with thermal insulation.
  • Heating methodology: Heating process is achieved through steam heat exchangers and pipes of various sizes. In few cases electricity and gas is also used for heating.
  • Humidity control: Humidity can be controlled in a kiln with help of introducing steam into the kiln through steam spray pipe. In order to limit the control of humidity, a proper ventilation system is built . There is ventilation system in all kinds of klin’
  • Air circulation: Air circulation is achieved through means of fans or blowers which may be installed inside and outside the kiln. Air circulation is important to carry heat and moisture away from the load.



Conventional kiln drying:

Under this method wood is dried in an installed structure where in temperature is about 200oF and humidity is controlled with the help of vent and steam spray. Air circulation achieved through fans with high velocities.


SPECIALIZED DRYING APPROACHES

DEHUMIDIFIED DRYING: Dehumidification kiln have several advantages. A boiler may be required for warm-up. In this process the water is condensed on coils of the dehumidifier and removed as water rather than allowing it to be vented to the atmosphere. Dehumidifier runs on electricity. However, in such processes there may be several risk such as inappropriate size of compressor can lead to failure of the process, electricity in few regions may be an expensive affair, etc.

SOLAR DRYING: This is a very eco-friendly method of drying wood in a kiln. It gives advantages like abundant energy availability, easy to build and operate and can be operated with direct as well as indirect solar energy. Such kilns can be used for even a small scale operation. There are 2 types of solar drying methods namely direct collection/greenhouse and indirect collection. Under both types there are 2 different procedures of drying i.e. direct method and solar with supplementary method.

VACUUM DRYING: Vacuum drying is a process of high temperature drying achieved through low temperatures. The process of vacuum drying is achieved by lowering the boiling temperature of water to be vaporized and removed at temperatures below 212oF. The difference between vacuum klin drying to other processes is the procedure in which heat is transferred to the lumber.

 

Reach us

#325 Mysore Road, Bangalore
Karnataka , 560 039
INDIA
Ph : +91 80 26746430